ผมมี Cisco 3620 + ISDN BRI และมีเบอร์ ISDN BRI (ตอนนี้ใช้เป็นโทรศัพท์เพื่อรับสายอย่างเดียว)
จะเอามาทำเป็น SIP Gateway เพื่อรับสายได้หรือไม่ครับ
ขอบคุณครับ
Moderator: jubjang
isdn switch-type basic-net3
!
!
voice rtp send-recv
!
voice service voip
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g711ulaw
!
interface Ethernet0/0
ip address 192.168.100.210 255.255.255.0
half-duplex
!
interface BRI1/0
no ip address
isdn switch-type basic-net3
isdn incoming-voice voice
isdn skipsend-idverify
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.100.1
!
!
dial-peer voice 100 pots
huntstop
destination-pattern 6645610000
direct-inward-dial
!
dial-peer voice 55200 voip
destination-pattern 55200
voice-class codec 1
session target ipv4:222.112.22.11
!
!
Apr 27 00:08:24.135: ISDN BR1/0 Q931: RX <- SETUP pd = 8 callref = 0x01
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Calling Party Number i = 0x2183, '890085550'
Plan:ISDN, Type:National
Apr 27 00:08:24.147: ISDN BR1/0 **ERROR**: accept_incoming_csm_call: modem problem Bearer capability not available(0x3A): b channel 0, call id 0x47
Apr 27 00:08:24.155: ISDN BR1/0 Q931: TX -> CALL_PROC pd = 8 callref = 0x81
Channel ID i = 0x89
Apr 27 00:08:24.179: ISDN BR1/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x81
Cause i = 0x80BA - Bearer capability not available
Apr 27 00:08:24.255: ISDN BR1/0 Q931: RX <- RELEASE pd = 8 callref = 0x01
Apr 27 00:08:24.267: ISDN BR1/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x81
Apr 27 00:08:36.551: ISDN BR1/0 Q931: RX <- RELEASE pd = 8 callref = 0x01
Cause i = 0x8290 - Normal call clearing
Slot 1:
BRI (S/T) Port adapter, 8 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.0 Board revision D0
Serial number 19743674 Part number 800-01237-03
FRU Part Number: NM-8B-S/T=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 21 01 00 01 2D 43 BA 50 04 D5 03 00 00 00 00
0x10: 68 00 00 00 00 04 24 17 FF FF FF FF FF FF FF FF
ย้อนกลับไปยัง Elastix - Unified Communications Software
กำลังดูบอร์ดนี้: ไม่มีสมาชิกใหม่ และ บุคคลทั่วไป 7 ท่าน